Cub Cadet 933 SWE Manual del operador

Printed In USASafe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty WARNINGREAD AND FOLLOW ALL SAFETY

Remove the oil filler cap/dipstick. If the level is low, slowly 3. add oil until oil level registers between high (H) and low (L), Fig. 3-9. Refer to

Auger and Drive Control CablesWARNING! Prior to operating your snow thrower, carefully read and follow all instructions below. Perform all adjustment

WARNING! Do not over-tighten the cable. Over-tightening may prevent the auger from disengaging and compromise the safety of the snow thrower.If adjus

Snow thrower controls and features are described below and illustrated in Fig. 4-1. Speed Selector LeverThe speed selector lever is located in the ri

Throttle ControlThe throttle control is located on the rear of the engine. It regulates the speed of the engine and will shut off the engine when move

Two-Way Chute-Pitch Control™The two-way chute-pitch control is located on the left side of the dash panel and is used to control the distance of snow

Starting The EngineWARNING! Always keep hands and feet clear of moving parts. Do not use a pressurized starting fluid. Vapors are flammable.NOTE: Allo

To Engage DriveWith the throttle control in the Fast (rabbit) position, move 1. shift lever into one of the six forward (F) positions or two reverse (

Replacing Shear PinsEach of the four auger spiral assemblies are secured to the spiral shaft with a shear pin and cotter pin. If the auger should stri

Slide the shave plate out of the off-set slot at the bottom 3. of the housing, and from between the skid shoes and side panels of the housing.With the

To The Owner12Record Product InformationBefore setting up and operating your new equipment, please locate the model plate on the equipment and record

Auger ShaftAt least once a season, one at a time, remove the shear pins from the auger shaft. Spray lubricant inside the hub of each auger spiral ass

Drive ControlRefer to “Auger and Drive Control Cables” of the Assembly & Set-Up - Section 3 for instructions to adjust the drive control. To furth

WARNING! To prevent accidental start-up, shut off the engine and remove the key before performing any type of engine maintenance.Periodic inspection a

Check that the spark plug washer is in good condition 4. and thread the spark plug in by hand to prevent cross-threading.After the spark plug is seate

Belt ReplacementBelt Removal PreparationRemove the chute crank assembly bracket by removing 1. the nuts and washers shown in Fig. 8-1. Remove the plas

Pull the brake bracket assembly towards the cable guide 3. roller and unhook the auger cable “Z” fitting. Refer to Fig. 8-5.From b4. oth sides of the

NOTE: Make sure to remove the piece of wood blocking the impeller.Check the auger drive belt adjustment. With the auger clutch lever in the disengage

Slide the hex shaft through the right side of the frame 10. toward the left side and through the friction wheel assembly.NOTE: If the sprocket fell

Off-Season StorageIf the snow thrower will not be used for 30 days or longer, the equipment needs to be stored properly. Follow storage instructions b

Troubleshooting829Problem Cause RemedyEngine fails to start Choke not in CHOKE position.1. Spark plug wire disconnected.2. Fuel tank empty or stale f

Important Safe Operation Practices23TrainingRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attempting to

Phone (800) 965-4CUB (4282) to order replacement parts or a complete Parts Manual (have your full model number and serial number ready). Parts Manual

Notes1131

32 se c t i O n 11— nO t e s

33se c t i O n 10 — nO t e s

MTD CONSUMER GROUP INC (MTD), the California Air Resources Board (CARB) and the United States Environment Protection Agency (U. S. EPA) Emission Contr

(4) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at a warra

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possession

4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafe Handling of GasolineTo avoid personal injury or property damage u

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sClearing a Clogged Discharge ChuteHand contact with the rotating impell

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may

AssemblyIMPORTANT: Two replacement auger shear pins are included with this manual (or stowed in the plastic handle panel). Refer to the Maintenance se

Chute AssemblyLoosen, but do not remove, the chute crank bracket in 1. order to attached the chute assembly. See Fig. 3-4.Remove lock nuts and screws

Set-UpShear PinsA pair of replacement auger shear pins and bow tie cotter pins have been included with your snow thrower. There are holes provided in