Cub Cadet 530 SWE Manual del operador

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOperatOr’s ManualSafe Operation Practices • Set-Up • Operation • Maintenance •

10 Section 3— ASSembly & Set-UpChute Clean-Out ToolThe chute clean-out tool is fastened to the top of the auger housing with a mounting clip and a

11Section 3 — ASSembly & Set-UpChute Assembly NOTE: Upper chutes on models with 4-Way Chute Control are also controlled by the Chute Directional

Controls and Features412Snow thrower controls and features are described below and illustrated in Figure 4-1. Shift LeverThe shift lever is located in

13Section 4 — controlS and FeatureSAuger ControlThe auger control is located on the left handle. Squeeze the control grip against the handle to engage

14 Section 4 — controlS and FeatureS2-Way Chute Directional Control (If so Equipped)The chute directional control is located on the left side of the d

Operation515Starting and Stopping the EngineRefer to the Engine Operator’s Manual packed with your snow thrower for instructions on starting and stopp

Maintenance & Adjustments616MaintenanceEngineRefer to the Engine Operator’s Manual.Tire PressureRefer to Assembly and Set-up section for informati

17Section 6 — Maintenance & adjuStMentSGear ShaftThe gear (hex) shaft should be lubricated at least once a season or after every twenty-five (25)

18 Section 6 — Maintenance & adjuStMentSDrive ControlWhen the drive control is released and in the disengaged “up” position, the cable should have

Se rvi ce719Belt ReplacementAuger BeltTo remove and replace your snow thrower’s auger belt, proceed as follows:1. Allow the engine to run until it is

Thank you for purchasing a Cub Cadet Snow Thrower. It was carefully engineered to provide excellent performance when properly operated and maintained

20 Section 7 — Service7. Remove the belt from around the auger pulley, and slip the belt between the support bracket and the auger pulley. See Figure

21Section 7 — Service6. Back out the stop bolt to increase the clearance between the friction wheel disc and friction wheel. See Figure 7-7.Stop Bolt

22 Section 7 — Service5. Carefully remove the hex nut which secures the hex shaft to the snow thrower frame and lightly tap the shaft’s end to dislod

Troubleshooting823Problem Cause RemedyEngine fails to start 1. Choke not in CHOKE position.2. Spark plug wire disconnected.3. Fuel tank empty or st

Replacement Parts924Component Part Number and Description954-04050 Auger Drive Belt (524 WE & 524 SWE)954-04260 Wheel Drive Belt (524 WE & 5

The following attachments and accessories are available for your Cub Cadet snow thrower. See your Cub Cadet dealer or the retailer from which you purc

Notes2611

27SectioN 11 — NoteS

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possession

Important Safe Operation Practices23Training1. Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to

4 Section 2 — important Safe operation practiceSSafe Handling of GasolineTo avoid personal injury or property damage use extreme care in handling gaso

5Section 2 — important Safe operation practiceSClearing a Clogged Discharge ChuteHand contact with the rotating impeller inside the discharge chute is

6 Section 2 — important Safe operation practiceSSafety SymbolsThis page depicts and describes safety symbols that may appear on this product. Read, u

Assembly & Set-Up37AssemblyRemove all loose parts before assembling.Handle Assembly1. Place the shift lever in the Forward-6 position2. Observe

8 Section 3— ASSembly & Set-Up2. Insert chute control rod into chute control head. Push rod as far into chute control head as possible, keeping t

9Section 3 — ASSembly & Set-Up6. Insert the chute control rod into the pinion gear below the joystick. Make sure to line up the hole in the rod w