Cub Cadet 945 SWE Manual del operador

Printed In USASafe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty WARNINGREAD AND FOLLOW ALL SAFETY

Rearward most hole of the actuator bracketsFigure 3-11Figure 3-12Adjust the lock nut as follows: 1. If adjusting the drive cable, thread the lock nut

NOTE: For detailed information on all engine controls, refer to the separate Engine Operator’s Manual supplied with this unit.Speed Selector Shift Le

Two-Way Chute Control™The two-way chute control is located on the left side of the dash panel and is used to control the distance of snow discharge fr

Chute Directional ControlThe chute directional control is located on the left side of the snow thrower.• To change the direction in which snow is thr

Starting and Stopping the EngineRefer to the Engine Operator’s Manual packed with your snow thrower for instructions on starting and stopping the engi

WheelsAt least once a season, remove both wheels. Clean and coat the axles with a multipurpose automotive grease before reinstalling wheels.Chute Dire

Shave Plate and Skid ShoesThe shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically an

Wheel drive controlRefer to the Adjustment section of the Assembly & Set-Up section earlier in this manual for instructions on how to adjust the w

Se rvice718Belt ReplacementBelt Removal Preparation1. Disconnect the chute crank assembly at the discharge chute end by removing the hairpin clip and

19Section 7 — Service2. Slip the auger control belt (the front belt) off the engine pulley. 3. Pull the brake bracket assembly towards the cable gui

To The Owner12Record Product InformationBefore setting up and operating your new equipment, please locate the model plate on the equipment and record

20 Section 7 — Service11. If also replacing the drive belt, proceed to the “Drive Belt” instruction. If not, reposition the transmission frame back

21Section 7 — Service9. Reposition the friction wheel assembly in the snow thrower frame. Insert the pin from the shift arm assembly into the frictio

Problem Cause RemedyExcessive vibration 1. Loose parts or damaged auger. 1. Stop engine immediately and disconnect spark plug wire. Tighten all bolt

Component Part Number and Description929-0071A Extension Cord, 110V954-04194A Auger Drive Belt954-04202 Wheel Drive Belt918-04178 Friction Wheel A

The following attachments and accessories are available for your Cub Cadet 945 series snow thrower. See your Cub Cadet dealer or the retailer from whi

No tes25

26

27

Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684 MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-

Important Safe Operation Practices23Training1. Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to

4 Section 2 — important Safe operation practiceSSafe Handling of GasolineTo avoid personal injury or property damage use extreme care in handling gaso

5Section 2 — important Safe operation practiceSClearing a Clogged Discharge ChuteHand contact with the rotating impeller inside the discharge chute is

6 Section 2 — important Safe operation practiceSSafety SymbolsThis page depicts and describes safety symbols that may appear on this product. Read, u

Figure 3-24. Looking beneath the handle panel, check that all of the cables (steering, auger, and drive) are properly routed and not pinched or kinke

3. Secure flange keeper removed earlier with lock nuts and screws. Tighten down nuts securing the other two flange keepers. See Figure 3-5. 4. Check

CAUTION: Operating a snow thrower equipped with steel skid shoes may result in damage to natural stone paver surfaces (e.g. sandstone, bluestone, lime