Cub Cadet 730 STE Manual del operador

Operator’s ManualPRINTED IN U.S.A.IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWARNING: This unit is equipped with an internal combustion en

10IMPORTANT: If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving part

11SECTION 4: MAKING ADJUSTMENTSWARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s m

12Shift Rod AdjustmentTo adjust the shift rod, proceed as follows:• Remove the hairpin clip and slide the shift rod connector up, to separate the uppe

13WARNING: If any adjustments need to be made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful

14SECTION 6: SERVICING YOUR SNOW THROWERWARNING: Before servicing, repairing, or inspecting, disengage all controls and stop engine. Wait until all m

15• Tip the snow thrower up and forward so that it rests on its auger housing. Refer to Figure 9.• Remove the six self-tapping screws from the frame c

16• Using a 7/8" wrench to hold the shaft, loosen, but do not completely remove, the hex bolt and bell washer on the left end of gear shaft. See

17SECTION 7: TROUBLESHOOTINGProblem Cause RemedyEngine fails to start 1. Fuel tank empty, or stale fuel.2. Blocked fuel line.3. Choke not in the ON p

18SECTION 8: PARTS LIST FOR MODEL 730 STE1111956177221127218Part of handle panel for reference only25493242014261119302932343839404142911454546474849

19Model 730 STERef. No.Part No. Part Description1. 684-0008A Shift Arm Assembly2. 705-5204A Chute Directional Control3. 710-0449 Carriage Screw 5/16-1

2TABLE OF CONTENTSFINDING MODEL NUMBERThis Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and mai

2010434744384619324517920313649231848502516331335152826222721121411165637168422813163037341414039242942Model 730 STE

21Model 730 STERef. No.Part No. Part Description1. 714-04040 Cotter Pin2. 756-0178 Flat Idler 3. 784-5632B Auger Idler Arm4. 710-0347 Hex Cap Screw 3/

22Model 730 STE152519262724232221161718192029303132323234303227261925362124232212 23010181920211311149376542403938288354133372929

23Model 730 STENOTE: For painted parts, please refer tothe list of color codes below. Please addthe applicable color code, whereverneeded, to the part

24Model 730 STE126310127854913151417161920222220192821182118151314293132303032343738362335273911404142444551464748524653515455545016174937242526263333

25Ref. No.Part No. Part Description1. 720-0223 Grip2. 710-0604A Tap Screw, 5/16-18 x.6253. 784-5642 Track Lockout Plate4. 710-0157 Hex Cap Screw, 5/16

26Model 730 STE172712345674891011121314151618191916161620212223242526Ref. No.Part No. Part Description1. 710-1652 Hex Washer Screw 1/4-20 x.6252. 731-

27Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-866-840-6483, 1-330-558-7220 MTD Canada Limited -

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESDANGER: This machine was built to be operated according to the rules for safe operation in this manual.

45. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. 6. Do not operate

5SECTION 1: ASSEMBLING YOUR SNOW THROWERUnpacking• Remove screws from the top sides and ends of the shipping crate.• Set panel aside to avoid tire pu

6Figure 3• If not already attached, unwrap the headlight wire which is attached to the headlight, beneath the handle panel. Wind the headlight wire ar

7The drive control also locks the auger control so youcan turn the chute directional control withoutinterrupting the snow throwing process. If the aug

8Track Lock LeverThe track lock lever is located on the right side of the snow thrower and is used to select the position of the auger housing and the

9• Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL.• Push primer button t