Cub Cadet 528 SWE Manual del operador

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma

Auger ControlWARNING! Prior to operating your snow thrower, carefully read and follow all instructions below. Perform all adjustments to verify your

Snow thrower controls and features are described below and illustrated in Fig. 4-1. NOTE: For detailed information on all engine controls, refer to

Stop SwitchThe stop switch is located on the rear of the engine. It will shut off the engine when moved into the STOP position.PrimerPressing the prim

Chute Directional ControlThe chute directional control is located on the left side of the dash panel.To change the direction in which snow is thrown,

Starting The EngineAttach spark plug wire to spark plug. Make certain the 1. metal loop on the end of the spark plug wire (inside the rubber boot) is

To Engage DriveWith the throttle control in the Fast (rabbit) position, move 1. shift lever into one of the six forward (F) positions or two reverse (

MaintenanceEngineRefer to the Briggs & Stratton Engine manual packed with your machine for all engine maintenance.Shave Plate and Skid ShoesThe s

Auger ShaftAt least once a season, remove the shear pins from the auger shaft. Spray lubricant inside the shaft and around the spacers along the shaft

Drive ControlWhen the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

Belt ReplacementAuger BeltTo remove and replace your snow thrower’s auger belt, proceed as follows:Allow the engine to run until it is out of fuel. 1.

Customer SupportIf you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this machine

Remove the belt from around the auger pulley, and slip the 7. belt between the support bracket and the auger pulley. See Fig. 8-5.Reassemble auger be

Slip the drive belt off the pulley and between friction 6. wheel and friction wheel disc. See Fig. 8-7.Remove and replace belt in the reverse order.7.

Problem Cause RemedyEngine fails to start Choke control not in ON position.1. Spark plug wire disconnected.2. Fuel tank empty or stale fuel.3. Engine

Component Part Number and Description929-0071 Extention Cord, 110V954-04050 Auger Drive Belt754-0367 Wheel Drive Belt684-04159 Friction Wheel Asse

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possession

Important Safe Operation Practices23TrainingRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attempting to

4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafe Handling of GasolineTo avoid personal injury or property damage u

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sClearing a Clogged Discharge ChuteHand contact with the rotating impell

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may

AssemblyHandlePlace the shift lever in the Forward-6 position1. Observe the lower rear area of the snow thrower to be sure 2. both cables are aligned

Finish securing chute control assembly to chute support 3. bracket with wing nut and hex screw removed earlier. See See Fig. 3-4.Check that all cable

Tire PressureBefore operating, check tire pressure and reduce pressure in both tires to between 15 psi and 20 psi. NOTE: If the tire pressure is not e