Cub Cadet 945 SWE Two-Stage Snow Thrower Manual del operador

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma

WARNING! Do not over-tighten the cable. Over-tightening may prevent the auger from disengaging and compromise the safety of the snow thrower.If adjus

Snow thrower controls and features are described below and illustrated in Fig. 4-1. NOTE: For detailed information on all engine controls, refer to

Primer BulbPressing the primer bulb forces fuel directly into the engine’s carburetor to aid in starting a “Cold” engine. NOTE: Do not use the primer

Two-Way Chute Control™The two-way chute control is located on the left side of the dash panel and is used to control the distance of snow discharge fr

Starting The EngineAttach spark plug wire to spark plug. Make certain the 1. metal loop on the end of the spark plug wire (inside the rubber boot) is

Operating TipsNOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature.WARNI

With the mounting holes toward the back, slide the new 4. shave plate into position and secure with the fasteners removed previously.LubricationGear S

Figure 6-5Auger ShaftAt least once a season, one at a time, remove the shear pins from the auger shaft. Spray lubricant inside the hub of each auger

Refer to “Auger and Drive Control Cables” of the Assembly & Set-Up - Section 3 for instructions to adjust the drive control. To further check the

Belt ReplacementBelt Removal PreparationDisconnect the chute crank assembly at the discharge 1. chute end by removing the hairpin clip and the flat wa

To The Owner12Record Product InformationBefore setting up and operating your new equipment, please locate the model plate on the equipment and record

Slip the auger control belt (the front belt) off the engine 2. pulley. Pull the 3. brake bracket assembly towards the cable guide roller and unhook t

If also replacing the drive belt, proceed to the “Drive Belt” 11. instruction. If not, reposition the transmission frame back onto the auger housing.

Slide the bearing onto the left end of the hex shaft and 14. press into the hole on the left side the frame.Place the belleville washer (rounded side

Off-Season StorageIf the snow thrower will not be used for 30 days or longer, the equipment needs to be stored properly. Follow storage instructions b

24Problem Cause RemedyEngine fails to start Choke control not in ON position.1. Spark plug wire disconnected.2. Fuel tank empty or stale fuel.3. Engin

Replacement Parts925Component Description Part NumberExtension Cord, 110V 929-0071Auger Drive Belt 954 -04131Wheel Drive Belt 954-0367Friction Wheel A

Notes1026

27se c t i O n 10 — nO t e s

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possession

Important Safe Operation Practices23TrainingRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attempting to

4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafe Handling of GasolineTo avoid personal injury or property damage u

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sMaintenance & StorageNever tamper with safety devices. Check their

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may

Secure the upper handle and lower handle with the two wing 4. nuts and carriage bolts removed earlier. Tighten the two wing nuts already installed in

Place chute assembly onto chute base as shown in Figure 3-5. Make sure that the chute notches engage with the spiral end of chute directional control,

Auger and Drive Control CablesWARNING! Prior to operating your snow thrower, carefully read and follow all instructions below. Perform all adjustment