Cub Cadet RZT L Manual de servicio

Service ManualRZT Zero Turn RiderMTD Products Inc. - Product Training and Education DepartmentFORM NUMBER - 769-0163612/2004NOTE: These materials are

66.11. Remove the front transmission mounting bolt using a 1/2” wrench and a 1/2” socket.NOTE: Secure the transmission or use another technician to su

7dure counts on the neutral control being cor-rectly adjusted.7.4. Start the engine. With the control rods discon-nected, the EZT should self-center t

87.11. The socket head cap screws that secure the neutral return assemblies to the EZTs act as a travel stop at the EZT end of the linkage. The lap ba

98. PIVOT BAR8.1. Safely lift and support the front of unit. 8.2. Disconnect the - (negative) lead to the battery.8.3. Using two 9/16” wrenches remove

108.8. Using a grease gun, fill the rest of the cavity AFTER final assembly. Filling before final assembly will allow the flange bearings to be pushed

119.5. Disconnect wires from the seat safety switch. See Figure 9.5.NOTE: Failure to reconnect seat safety switch will cause unit not to run.Figure 9.

1210.1. Disconnect the - (negative) lead to the battery.10.2. Using a 1/2” wrench, remove the three screws securing the console to the seat frame.

1310.9. If any electrical connections are present discon-nect or remove switch from console. See Figure 10.9.NOTE: The throttle cable a

1411.9. Remove right side console as per “CONSOLE REMOVAL” of this manual.11.10. With the right side console removed the battery will slip out the sid

1512.6. Remove the left console as described in the “CONSOLE REMOVAL” section of this manual.12.7. Rotate tank upward and slide out toward the side. S

www.mymowerparts.comK&T Saw Shop 606-678-9623 or 606-561-4983

1613.6. While rotating the control hub forward the lapbar control rod can be disconnected and removed. See Figure 13.6.13.7. Pull the control hub off

1714. DECK LIFT SHAFT REPLACEMENT14.1. The following section of this manual need to be accomplished:DECK REMOVAL SEAT REMOVALCONSOLE REMOVAL, RIGHT AN

1814.8. Using two 9/16” wrenches remove the bolt, nut, and spring on the brake handle on the left han-dle side of the deck lift shaft. See Figure 14.8

1914.14.Carefully release the tension on the deck lift handle torsion spring. See Figure 14.14.NOTE: Putting the deck lift handle in the lowest cuttin

2015. ELECTRICAL SYSTEM COMPONENTSThis section is intended to help technicians identify the location and function of specific components on the RZT el

2115.3. The NEUTRAL SWITCHES are in the console on each side of the unit. They are normally open/normally closed switches. See Figure 15.3.-The two i

2215.5. The PTO switch is located on the right console behind the key switch. This switch is part of the start circuit, PTO run circuit, and reverse s

2315.7. There are three RELAYS in the electrical system of the RZT. They are located under the right side console toward the rear. See Figure 15.7.-Th

24Figure 15.8Starter solenoidwww.mymowerparts.comK&T Saw Shop 606-678-9623 or 606-561-4983

25www.mymowerparts.comK&T Saw Shop 606-678-9623 or 606-561-4983

Cub Cadet RZTDeck Leveling ... 1PTO / Dec

26www.mymowerparts.comK&T Saw Shop 606-678-9623 or 606-561-4983

www.mymowerparts.comK&T Saw Shop 606-678-9623 or 606-561-4983

1617AA5A7P7101D224G200732004 is the first year for the RZT. There are two mod-els RZT17 and RZT22. Now for the ‘05 model year is Kohler Command 19

22. PTO / DECK BELT REPLACEMENT2.1. Insert a 1/2” breaker bar into the square hole in the tensioner arm located on top of the deck. See Figure 2.1.2.2

34. DRIVE BELT REPLACEMENT4.1. Insert a 1/2” breaker bar into the square hole on the tensioner arm.4.2. Pull the breaker bar to the right until it can

45.6. Use a 9/16” socket to adjust the air gap on the clutch to between.010” and.015”. See Figure 5.6. NOTE: Clu

56.6. Mark the lap bar control rod threads near the cle-vis pin. See Figure 6.6.6.7. Remove the hairpin securing the lap bar control rod to the transm