Cub Cadet RT 45 Manual del operador

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma

Set-UpTiresThe tires on your tiller may be over-inflated for shipping purposes. Reduce the tire pressure before operating the tiller. Recommended ope

Clutch ControlGear Selection HandleHandle Adjustment LockDepth StakeFigure 4-1Engine ControlsSee the separate Engine Operator’s Manual for additional

Starting the EngineWARNING! Read, understand, and follow all the instructions and warnings on the machine and in this manual before operating.NOTE: Wh

To adjust the side shields, remove the wing nuts. Move the 7. side shield to the desired position and replace the wing nuts. Tighten securely. See Fig

WARNING! Disconnect the spark plug wire and ground it against the engine before performing any maintenance or repairs.MaintenanceEngineRefer to the se

Idler Pulley RodAfter the belt tension has been adjusted, if the belt is excessively stretched, you may need to adjust the idler pulley rod. This can

Maintenance ScheduleFirst 5 HoursEach Use or Every 5 Hrs.Every Season or 25 HoursEvery Season or 50 HoursEvery Season or 100 HoursService DatesCheck

Reinstall the drain plug and tighten it securely.3. Refill with the recommended oil and check the oil level. 4. Refer to the Assembly & Set-up sec

To clean foam element, separate it from the paper element 2. and wash in liquid detergent and water. Allow to dry thoroughly before using. Do not oil

Off-Season StorageEngines stored between 30 and 90 days need to be treated with a gasoline stabilizer and engines stored over 90 days need to be drain

Customer SupportIf you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this machine

Belt ReplacementYour tiller has been engineered with a belt designed for long life and optimal performance. It should never be replaced with a non-OEM

Problem Cause RemedyEngine fails to start Fuel tank empty or stale fuel.1. Throttle control lever not in correct starting 2. position (if equipped).Bl

Component Part Number and Description954-0434 Belt, 4L x 58.16742-0305A-0637 Articulating Tine946-1117 Clutch Cable934-04365 Tires, 16 x 4.6 x 87

Notes1123

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possession

Important Safe Operation Practices23TrainingRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attempting to

4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sAfter striking a foreign object, stop the engine, disconnect 11. the

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sIf the fuel tank has to be drained, do this outdoors.9. Observe proper

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may

Contents of CartonOne Tiller • One Handlebar Assembly• One Shift Rod• One Depth Stake• One Operator’s Manual• One Engine Operator’s Manual• Assemb

Handlebar AssemblyRemove the top two bolts and flange lock nuts from the 1. handle mounting brackets, but do not remove the bottom bolt and nut. See F

Control RodMake sure the handle assembly is in the highest position. 1. Refer to the Controls & Features Section.Remove the hairpin clips from the